1z 6-DIGIT 0.56" RED SUNLIGHT READABLE DISPLAYz 4 SEPARATE DISPLAYS (Timer, Counter, Real-Time Clock, and Date)z CYCLE COUNTING CAPABILITYz PROGR
10PROGRAMMING MODE ENTRY (PAR KEY)The Programming Mode is entered by pressing the PAR key. If this mode isnot accessible, then meter programming is lo
11This parameter determines how the Timer Input Signals affect the“Run/Stop” status of the Timer. The timing diagrams below reflect a Sinkinginput set
12ª«ª«NO FUNCTIONWith this selection, NO function is performed. This is the factory setting forall user inputs and function keys except th
13ª«ª«DISPLAY HOLD and RESET (Edge Triggered Reset)When activated, the meter “freezes” the display values entered as in thesub
14When active (maintained action), the meter “holds” (maintains) the presentoutput state for all Setpoints entered as in the sublist. Does not app
156.3 MODULE 3 - DISPLAY AND PROGRAM LOCK-OUTPARAMETERS ()Module 3 is the programming module for setting the Display Lock-outParameters and t
166.4 MODULE 4 - CYCLE COUNTERPARAMETERS ()PARAMETER MENUModule 4 is the programming module for the Cycle Counter Parameters. In theDisplay Mode
17Timing Diagrams for Predefined Timer Operating ModesNOTE: Input A is shown as a Sourcing input (active high). If a Sinking input (active low) is use
18ª«SETPOINT ACTIONThis parameter determines the mode for output deactivation as shown below.Output activation is controlled by the SETPOINT
19DISPLAY DESCRIPTION FACTORYSundayMondaySaturdayFridayThursdayWednesdayTuesdayTIME-OUT VALUE to
2Ordering Information . . . . . . . . . . . . . . . . . . . 2General Meter Specifications. . . . . . . . . . . . . 3Optional Plug-In Cards and Accesso
206.7 MODULE 7 - SERIAL COMMUNICATIONS PARAMETERS ()PARAMETER MENUThis module can only be accessed if a Serial Communications Card is installed.*
21SERIAL RTC MASTER ADDRESSINGA meter, having software code version 2.3 or greater, with a Real Time ClockCard and an RS485 Serial Communication Card
Full Transmission ( = )✰These characters only appear in the last line of a block print.The first two characters transmitted are the unit address
23Module 8 is the programming module for the Real-Time Clock (RTC) Dateand Time Parameters. In the Display Mode, the DAT annunciator indicates theRTC
24TIME DISPLAY FORMATª«DATE DISPLAY FORMATAUTO CHANGE FOR DAYLIGHT SAVINGS TIMESelect the format in which the Real-Time Clock Time will be d
25PARAMETER MENURESTORE FACTORY DEFAULTSUse the RST and/or arrow keys to display andpress PAR. The meter will display and then returnst
265-OPEr Timer Operating ModesDISPLAY PARAMETER USER SETTINGFACTORYSETTINGUSEr-1USER INPUT 1NOUSEr-2USER INPUT 2NOUSEr-3USER INPUT 3NOF1FUNCTION KEY 1
277-SrL Serial Communication ParametersDISPLAY PARAMETERFACTORYSETTINGUSER SETTINGbAUdBAUD RATE9600dAtADATA BITS7PArPARITY BITOddAddrMETER UNIT ADDRES
Timer RangeF1/F2 KeysTimer InputOperationTimer InputFilteringTimingDirectionTimer St
3GENERAL METER SPECIFICATIONS1. DISPLAY: 6 digit, 0.56" (14.2 mm) red sunlight readable or standard greenLED2. POWER:AC Versions (PAXCK000, PAXTM
4OPTIONAL PLUG-IN CARDS AND ACCESSORIESWARNING: Disconnect all power to the unit beforeinstalling Plug-in cards.Adding Option CardsThe PAX and MPAX se
5Installation The meter meets NEMA 4X/IP65 requirements for indoor use when properlyinstalled. The meter is intended to be mounted into an enclosed pa
63.0 INSTALLING PLUG-IN CARDSThe Plug-in cards are separately purchased optional cards that performspecific functions. These cards plug into the main
7Before connecting the wires, the Timer Input logic jumper should be verified for proper position.4.2 TIMER INPUT WIRINGCAUTION: Timer Input common i
84.4 SETPOINT (ALARMS) WIRINGSETPOINT PLUG-IN CARD TERMINALSSINKING OUTPUT LOGIC CARDSOURCING OUTPUT LOGIC CARD4.5 SERIAL COMMUNICATION WIRINGRS232
9Time synchronization between multiplePAXCK meters can be accomplished through ahardware interface on the Real-Time Clock optioncard. This RS485 type
Kommentare zu diesen Handbüchern