Red-lion P16 Bedienungsanleitung PDF herunterladen

-0.0

+0.6

-0.000

+0.024

-0.0

+0.6

-0.000

+0.024

(45 )

1.772

(45 )

1.772

(9.4)

0.37

4.17 (105.9)

1.95

(49.5)

1.76 (44.7)

1.76

(44.7)

1413

MODELS T16 & P16 - TEMPERATURE/PROCESS CONTROLLERS

GENERAL DESCRIPTION

The Model T16 Controller accepts signals from a variety of temperature

sensors (thermocouple or RTD), while the Model P16 Controller accepts either a

0 to 10 VDC or 0/4 to 20 mA DC input signal. Both controllers can provide an

accurate output control signal (time proportional or DC Analog Output) to

maintain a process at a setpoint value. Dual 4-digit displays allow viewing of the

process/temperature and setpoint simultaneously. Front panel indicators inform

the operator of the controller and output status. The comprehensive programming

allows these controllers to meet a wide variety of application requirements.

MAIN CONTROL

The controller operates in the PID Control Mode for both heating and

cooling, with on-demand auto-tune, that establishes the tuning constants. The

PID tuning constants may be fine-tuned through the front panel and then locked

out from further modification. The controller employs a unique overshoot

suppression feature, that allows the quickest response without excessive

overshoot. Switching to Manual Mode provides the operator direct control of the

output. The controller may also be programmed to operate in On/Off mode with

adjustable hysteresis.

ALARMS

Optional alarm(s) can be configured independently for absolute high or low

acting with balanced or unbalanced hysteresis. They can also be configured for

deviation and band alarm. In these modes, the alarm trigger values track the

setpoint value. Adjustable alarm hysteresis can be used for delaying output

response. The alarms can be programmed for Automatic or Latching operation.

A selectable standby feature suppresses the alarm during power-up until the

temperature stabilizes outside the alarm region.

ANALOG OUTPUT OPTION

The optional DC Analog Output (10 V or 20 mA) can be configured and

scaled for control or re-transmission purposes. The programmable output update

time reduces valve or actuator activity.

PC PROGRAMMING KIT

The optional TP16KIT contains a programming module with a 9 pin RS232

connector, cable and Crimson, a Windows

based configuration software. The

software allows downloading, uploading and storage of T16 and P16 program

files. All controllers have a communications port that allows configuration by

PC even without controller power connected. Controller calibration is also

possible using the software when the proper calibration equipment and

controller power is connected.

CONSTRUCTION

The controller is constructed of a lightweight, high impact, black plastic

textured case and bezel with a clear display window. The front panel meets

NEMA 4X/IP65 specifications when properly installed. In applications that do

not require protection to NEMA 4X, multiple controllers can be stacked

horizontally or vertically. Modern surface-mount technology, extensive testing,

plus high immunity to noise interference makes the controller extremely reliable

in industrial environments.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that appear in the

manual or on equipment must be observed to ensure personal safety and to

prevent damage to either the instrument or equipment connected to it. If

equipment is used in a manner not specified by the manufacturer, the protection

provided by the equipment may be impaired.

Do not use the controller to directly command motors, valves, or other actuators

not equipped with safeguards. To do so can be potentially harmful to persons or

equipment in the event of a fault to the controller. An independent and redundant

temperature limit indicator with alarm outputs is strongly recommended.

 PID CONTROL WITH REDUCED OVERSHOOT

 T16 ACCEPTS TC AND RTD

 P16 ACCEPTS 0-10 V AND 0/4-20 mA SIGNALS

 ON DEMAND AUTO-TUNING OF PID SETTINGS

 DC ANALOG OUTPUT (OPTIONAL)

 USER PROGRAMMABLE FUNCTION BUTTON

 PC OR FRONT PANEL PROGRAMMING

 PC CONFIGURABLE WITH TP16KIT

DIMENSIONS In inches (mm)

PANEL CUT-OUT

UL Recognized Component,

File #E156876

CAUTION: Risk of Danger.

Read complete instructions prior to

installation and operation of the unit.

CAUTION: Risk of electric shock.

Bulletin No. T/P16-L

Drawing No. LP0486

Released 8/13

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

www.redlion.net

1 2 3 4 5 6 ... 27 28

Inhaltsverzeichnis

Seite 1 - DIMENSIONS In inches (mm)

-0.0+0.6-0.000+0.024-0.0+0.6-0.000+0.024(45 )1.772(45 )1.772(9.4)0.374.17 (105.9)1.951.95(49.5)(49.5)221OO1AARMAN%WP%1.76 (44.7)115121.76(44

Seite 2 - GENERAL SPECIFICATIONS

107.0 progrAmming: ConFigurAtion loop LOOPHIDDEN DISPLAYLOOPPARAMETERSINPUTMODULE MODULEOUTPUTPARAMETERSLOCKOUTPARAMETER

Seite 3 - ORDERING INFORMATION

117.1 module 1 - input pArAmeterS (1-IN) t16 only   INPUTTYPETEMPSCALEDECIMALRESOLUTIONDIGITALFILTERING OFFSETSHIFT/HIGH L

Seite 4 - BLOCK DIAGRAM

127.1 module 1 - input pArAmeterS (1-IN) p16 only  INPUTTYPEPERCENTSYMBOLDECIMALRESOLUTIONROUNDINGINCREMENTINPUTVALUE 1DISPL

Seite 5 - 2.0 inStAlling the Controller

132I2INPUT VALUE SCALING POINT 2 to 2 mA to 1 VFor Key-in Method, enter the second coordinate Input Value by using the arrow

Seite 6 - 3.0 Wiring the Controller

142CYCLE TIME to 2 secondsOUTPUT POWER DAMPENING to 2 secondsThe Cycle Time is entered in seconds with one tenth of a second resolutio

Seite 7 - 5.0 progrAmming: diSplAy loop

152ANALOG OUTPUT RANGE (OPTIONAL)1 V 2 mA2 mASelect the type of output and range. The Analog output jumpers are factory set to cu

Seite 8

167.4 module 4 - AlArm pArAmeterS (4-AL) (optionAl)ACt1 rSt1Lit1Stb1AL-1ACt2 Lit2ALARM 1ACTIONALARM 1ANNUNCIATORALARM 1RESET ANNUNCIATORALARM 2ALARM 2

Seite 9 - 6.0 progrAmming: hidden loop

17nLit1ALARM ANNUNCIATOR ALARM 1With normal selection, the alarm annunciator indicates “on” alarm output 1. With reverse selection, the alarm annunc

Seite 10 - FRONT DISPLAY

18CYCLE TIME to 2 secondsThis cycle time functions like the O1 Output Cycle Time but allows independent cycle time for cooling. A setting of ze

Seite 11 - 1-IN) t16 only

19The controller is fully calibrated from the factory. Recalibration is recommended every two years by qualified technicians using appropriate equipme

Seite 12 - 1-IN) p16 only

2INPUT SPECIFICATIONS1. SENSOR INPUT:Sample Period: 100 msec (10 Hz rate)Step Response Time: 300 msec typical, 400 msec max to within 99% of final val

Seite 13

20RESTORE FACTORY SETTINGSPress and hold B to display  . Press A. The controller will display  and then return to F. Press L to ret

Seite 14

21ON/OFF CONTROLThe controller operates in On/Off Control when the Proportional Band is set to 0.0%. In this control mode, the process will constantly

Seite 15 - SELECTION DESCRIPTION

22TIME PROPORTIONAL PID CONTROLIn Time Proportional applications, the output power is converted into output On time using the Cycle Time. For example,

Seite 16 - 4-AL) (optionAl)

23PID AdjustmentsIn some applications, it may be necessary to fine tune the Auto-Tune calculated PID parameters. To do this, a chart recorder or data

Seite 17 -  to 

24PARAMETER VALUE CHARTProgrammer:______________________Date:_________Controller Number:_______ Security Code:_______DISPLAY PARAMETER FACTORY SETTING

Seite 18 - CYC2 db-2gAN2

25t16 & p16 progrAmming QuiCK overvieW1-IN tYPE PCt SCAL dCPt rnd FLtr dSP1 INP1dSP2Input TypePercent SymbolTempScaleDecimal ResolutionRounding In

Seite 19 -  

26This page intentionally left blank

Seite 20 - , press A

27This page intentionally left blank

Seite 21 - Control mode explAnAtionS

LIMITED WARRANTYThe Company warrants the products it manufactures against defects in materials and workmanship for a period limited to two years from

Seite 22 - AUTO-TUNE CODES 0 TO 2

3OUTPUT SPECIFICATIONS1. CONTROL AND ALARM OUTPUTS:Relay Output:Type: Form AContact Rating: 3 A @ 250 VAC or 30 VDC (resistive load)Life Expectancy: 1

Seite 23 - MANUAL TUNING

4EMC INSTALLATION GUIDELINESAlthough Red Lion Controls Products are designed with a high degree of immunity to Electromagnetic Interference (EMI), pro

Seite 24

51.0 Setting the JumperS (AnAlog output modelS only)To insure proper operation, the Analog Output jumpers must be set to the same range selected in p

Seite 25 - Setpoint

63.0 Wiring the ControllerWIRING CONNECTIONSAll wiring connections are made to the rear screw terminals. When wiring the controller, use the numbers o

Seite 26

7FRONT PANEL KEYSThe F1 key is pressed to exit (or escape) directly to the start of the Display Loop. While in the Display Loop, the F1 key can be pre

Seite 27

8SETPOINT VALUE (SP1) *SETPOINT VALUE (SP2) * to 22% OUTPUT POWER *1 to 1 to Typically, the controller is operating w

Seite 28 - LIMITED WARRANTY

6.0 progrAmming: hidden loopHIDDEN LOOPNote: Parameters shown bold are the only parameters visible in the Hidden Loop with Factory Settings. Setpoint